/******************************************************************************
 *
 * Copyright(c) 2007 - 2013 Realtek Corporation. All rights reserved.
 *                                        
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of version 2 of the GNU General Public License as
 * published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful, but WITHOUT
 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
 * more details.
 *
 * You should have received a copy of the GNU General Public License along with
 * this program; if not, write to the Free Software Foundation, Inc.,
 * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
 *
 *
 ******************************************************************************/
#define _HCI_HAL_INIT_C_

//#include <drv_types.h>
#include <rtl8192e_hal.h>


#ifndef CONFIG_USB_HCI

#error "CONFIG_USB_HCI shall be on!\n"

#endif


static void _dbg_dump_macreg(_adapter *padapter)
{
	u32 offset = 0;
	u32 val32 = 0;
	u32 index =0 ;
	for(index=0;index<64;index++)
	{
		offset = index*4;
		val32 = rtw_read32(padapter,offset);
		DBG_8192C("offset : 0x%02x ,val:0x%08x\n",offset,val32);
	}
}

static VOID
_ConfigChipOutEP_8192E(
	IN	PADAPTER	pAdapter,
	IN	u8		NumOutPipe
	)
{
	HAL_DATA_TYPE	*pHalData	= GET_HAL_DATA(pAdapter);


	pHalData->OutEpQueueSel = 0;
	pHalData->OutEpNumber = 0;

	switch(NumOutPipe){
		case 	4:
				pHalData->OutEpQueueSel=TX_SELE_HQ| TX_SELE_LQ|TX_SELE_NQ | TX_SELE_EQ;
				pHalData->OutEpNumber=4;
				break;		
		case 	3:
				pHalData->OutEpQueueSel=TX_SELE_HQ| TX_SELE_LQ|TX_SELE_NQ;
				pHalData->OutEpNumber=3;
				break;
		case 	2:
				pHalData->OutEpQueueSel=TX_SELE_HQ| TX_SELE_NQ;
				pHalData->OutEpNumber=2;
				break;
		case 	1:
				pHalData->OutEpQueueSel=TX_SELE_HQ;
				pHalData->OutEpNumber=1;
				break;
		default:				
				break;
			
	}
	DBG_871X("%s OutEpQueueSel(0x%02x), OutEpNumber(%d) \n",__FUNCTION__,pHalData->OutEpQueueSel,pHalData->OutEpNumber );

}

static BOOLEAN HalUsbSetQueuePipeMapping8192EUsb(
	IN	PADAPTER	pAdapter,
	IN	u8		NumInPipe,
	IN	u8		NumOutPipe
	)
{
	HAL_DATA_TYPE	*pHalData	= GET_HAL_DATA(pAdapter);
	BOOLEAN			result		= _FALSE;

	_ConfigChipOutEP_8192E(pAdapter, NumOutPipe);
	
	// Normal chip with one IN and one OUT doesn't have interrupt IN EP.
	if(1 == pHalData->OutEpNumber){
		if(1 != NumInPipe){
			return result;
		}
	}

	// All config other than above support one Bulk IN and one Interrupt IN.
	//if(2 != NumInPipe){
	//	return result;
	//}

	result = Hal_MappingOutPipe(pAdapter, NumOutPipe);
	
	return result;

}

void rtl8192eu_interface_configure(_adapter *padapter)
{
	HAL_DATA_TYPE	*pHalData	= GET_HAL_DATA(padapter);
	struct dvobj_priv	*pdvobjpriv = adapter_to_dvobj(padapter);
	struct registry_priv  *registry_par = &padapter->registrypriv;

	if (IS_HIGH_SPEED_USB(padapter))
	{
		pHalData->UsbBulkOutSize = USB_HIGH_SPEED_BULK_SIZE;//512 bytes
	}
	else
	{
		pHalData->UsbBulkOutSize = USB_FULL_SPEED_BULK_SIZE;//64 bytes
	}

	pHalData->interfaceIndex = pdvobjpriv->InterfaceNumber;

#ifdef CONFIG_USB_TX_AGGREGATION
	pHalData->UsbTxAggMode		= 1;
	pHalData->UsbTxAggDescNum	= 3;	// only 4 bits
#endif

#ifdef CONFIG_USB_RX_AGGREGATION

	pHalData->UsbRxAggMode = registry_par->usb_rxagg_mode;

	if(( pHalData->UsbRxAggMode != USB_RX_AGG_DMA) && ( pHalData->UsbRxAggMode != USB_RX_AGG_USB))
	{		
		pHalData->UsbRxAggMode = USB_RX_AGG_DMA;// USB_RX_AGG_USB,	USB_RX_AGG_MIX;
	}
	//pHalData->UsbRxAggBlockCount	= 8; //unit : 512b
	//pHalData->UsbRxAggBlockTimeout	= 0x6;
	
	//pHalData->UsbRxAggPageCount	= 16; //uint :128 b //0x0A;	// 10 = MAX_RX_DMA_BUFFER_SIZE/2/pHalData->UsbBulkOutSize
      //pHalData->UsbRxAggPageTimeout = 0x6; //6, absolute time = 34ms/(2^6)
	if(pHalData->UsbRxAggMode	 == USB_RX_AGG_DMA)
	{
		pHalData->RegAcUsbDmaSize = 8;// unit 1k for Rx DMA aggregation mode
		pHalData->RegAcUsbDmaTime = 8;//unit 32us
	}
	else if(pHalData->UsbRxAggMode == USB_RX_AGG_USB)
	{
#ifdef CONFIG_PLATFORM_HISILICON
		pHalData->RegAcUsbDmaSize = 3; /*unit 4k for USB aggregation mode */
		pHalData->RegAcUsbDmaTime = 8; /*unit 32us*/
#else
		pHalData->RegAcUsbDmaSize = 6; /* unit 4k for USB aggregation mode */
		pHalData->RegAcUsbDmaTime = 0x20; /* unit 32us */
#endif	
	}
#endif

	HalUsbSetQueuePipeMapping8192EUsb(padapter,
				pdvobjpriv->RtNumInPipes, pdvobjpriv->RtNumOutPipes);

}

static VOID
_InitBurstPktLen_8192EU(IN PADAPTER Adapter)
{
#if 0
	u1Byte speedvalue, provalue, temp;
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
 	

	//PlatformEFIOWrite2Byte(Adapter, REG_TRXDMA_CTRL_8195, 0xf5b0);
	//PlatformEFIOWrite2Byte(Adapter, REG_TRXDMA_CTRL_8812, 0xf5b4);
	PlatformEFIOWrite2Byte(Adapter, REG_RXDMA_STATUS_8192E, 0x7400);  //burset lenght=4, set 0x3400 for burset length=2
	PlatformEFIOWrite1Byte(Adapter, 0x289,0xf5);				//for rxdma control
	//PlatformEFIOWrite1Byte(Adapter, 0x3a, 0x46);

	// 0x456 = 0x70, sugguested by Zhilin
	//PlatformEFIOWrite1Byte(Adapter, REG_AMPDU_MAX_TIME_8192E, 0x70);

	//Suggention by SD1 Jong and Pisa, by Maddest 20130107.
	PlatformEFIOWrite2Byte(Adapter, REG_MAX_AGGR_NUM_8192E, 0x0e0e);
	PlatformEFIOWrite1Byte(Adapter, REG_FWHW_TXQ_CTRL_8192E, 0x80);//EN_AMPDU_RTY_NEW
	PlatformEFIOWrite1Byte(Adapter, REG_AMPDU_MAX_TIME_8192E, 0x5e);
	PlatformEFIOWrite4Byte(Adapter, REG_FAST_EDCA_CTRL_8192E, 0x03087777);
	

	//PlatformEFIOWrite4Byte(Adapter, 0x458, 0xffffffff);
	PlatformEFIOWrite1Byte(Adapter, REG_USTIME_TSF_8192E, 0x50);
	PlatformEFIOWrite1Byte(Adapter, REG_USTIME_EDCA_8192E, 0x50);

	if(IS_HARDWARE_TYPE_8821U(Adapter) ||IS_HARDWARE_TYPE_8192EU(Adapter))
		speedvalue = BIT7;	
	else
		speedvalue = PlatformEFIORead1Byte(Adapter, 0xff); //check device operation speed: SS 0xff bit7

	if(speedvalue & BIT7)   //USB2/1.1 Mode
	{
		temp = PlatformEFIORead1Byte(Adapter, REG_USB_INFO);
		if(((temp>>4)&0x03)==0)
		{
			//pHalData->UsbBulkOutSize = 512;
			provalue = PlatformEFIORead1Byte(Adapter, REG_RXDMA_PRO_8192E);
			PlatformEFIOWrite1Byte(Adapter, REG_RXDMA_PRO_8192E, (provalue|BIT(4)&(~BIT(5)))); //set burst pkt len=512B
			PlatformEFIOWrite2Byte(Adapter, REG_RXDMA_PRO_8192E, 0x1e);
		}
		else
		{
			//pHalData->UsbBulkOutSize = 64;
			provalue = PlatformEFIORead1Byte(Adapter, REG_RXDMA_PRO_8192E);
			PlatformEFIOWrite1Byte(Adapter, REG_RXDMA_PRO_8192E, ((provalue|BIT(5))&(~BIT(4)))); //set burst pkt len=64B
		}

		PlatformEFIOWrite2Byte(Adapter, REG_RXDMA_AGG_PG_TH_8192E,0x2005); //dmc agg th 20K

        pHalData->bSupportUSB3 = FALSE;
	}

	PlatformEFIOWrite1Byte(Adapter, REG_DWBCN0_CTRL_8192E, 0x10);

	PlatformEFIOWrite1Byte(Adapter, 0x4c7,PlatformEFIORead1Byte(Adapter, 0x4c7)|BIT(7)); //enable single pkt ampdu
	PlatformEFIOWrite1Byte(Adapter, REG_RX_PKT_LIMIT_8192E, 0x18);		//for VHT packet length 11K

	//PlatformEFIOWrite1Byte(Adapter, REG_MAX_AGGR_NUM_8192E, 0x1f);
	PlatformEFIOWrite1Byte(Adapter, REG_PIFS_8192E, 0x00);
	//PlatformEFIOWrite1Byte(Adapter, REG_FWHW_TXQ_CTRL_8192E, PlatformEFIORead1Byte(Adapter, REG_FWHW_TXQ_CTRL)&(~BIT(7)));

#ifdef CONFIG_TX_EARLY_MODE
	if(pHalData->AMPDUBurstMode)
	{
		PlatformEFIOWrite1Byte(Adapter,REG_SW_AMPDU_BURST_MODE_CTRL_8192E,  0x5F);
	}
#endif

	PlatformEFIOWrite1Byte(Adapter, 0x1c, PlatformEFIORead1Byte(Adapter, 0x1c) | BIT(5) |BIT(6));  //to prevent mac is reseted by bus. 20111208, by Page
#endif
}

static u32 _InitPowerOn_8192EU(_adapter *padapter)
{
	u16 value16;
	u32 value32;
	HAL_DATA_TYPE	*pHalData	= GET_HAL_DATA(padapter);
	// HW Power on sequence
	u8 bMacPwrCtrlOn=_FALSE;

	rtw_hal_get_hwreg(padapter, HW_VAR_APFM_ON_MAC, &bMacPwrCtrlOn);
	if(bMacPwrCtrlOn == _TRUE)	
		return _SUCCESS;

	DBG_871X("==>%s \n",__FUNCTION__);
	value32 = rtw_read32(padapter, REG_SYS_CFG1_8192E);

	if(value32 & BIT_SPSLDO_SEL){
		//LDO
		rtw_write8(padapter, REG_LDO_SWR_CTRL, 0xC3); 
	}
	else	{
		//SPS
		//0x7C [6] = 1¡¦b0 (IC default, 0x83)
	
#ifndef CONFIG_PLATFORM_HISILICON
		/* 0x14[23:20]=b¡¦0101 (raise 1.2V voltage)
		   u1Byte	tmp1Byte = PlatformEFIORead1Byte(Adapter,0x16);
		   PlatformEFIOWrite1Byte(Adapter,0x16,tmp1Byte |BIT4|BIT6); */

		u32 voltage = (rtw_read32(padapter, REG_SYS_SWR_CTRL2_8192E) & 0xFF0FFFFF) | (0x05 << 20);

		rtw_write32(padapter, REG_SYS_SWR_CTRL2_8192E, voltage);
#endif	/*CONFIG_PLATFORM_HISILICON*/
		rtw_write8(padapter, REG_LDO_SWR_CTRL, 0x83);
	}

	//adjust xtal/afe before enable PLL, suggest by SD1-Scott
	Hal_CrystalAFEAdjust(padapter);

	if(!HalPwrSeqCmdParsing(padapter, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, Rtl8192E_NIC_ENABLE_FLOW)){
		DBG_871X("%s: HalPwrSeqCmdParsing fail\n", __func__);
		return _FAIL;	
	}

	// Enable MAC DMA/WMAC/SCHEDULE/SEC block
	// Set CR bit10 to enable 32k calibration. Suggested by SD1 Gimmy. Added by tynli. 2011.08.31.
	rtw_write16(padapter, REG_CR, 0x00);  //suggseted by zhouzhou, by page, 20111230
	value16 = rtw_read16(padapter, REG_CR);
	value16 |= (HCI_TXDMA_EN | HCI_RXDMA_EN | TXDMA_EN | RXDMA_EN
				| PROTOCOL_EN | SCHEDULE_EN | ENSEC | CALTMR_EN);
	rtw_write16(padapter, REG_CR, value16);

	bMacPwrCtrlOn = _TRUE;
	rtw_hal_set_hwreg(padapter, HW_VAR_APFM_ON_MAC, &bMacPwrCtrlOn);
     
	return _SUCCESS;
}

//---------------------------------------------------------------
//
//	MAC init functions
//
//---------------------------------------------------------------

// Shall USB interface init this?
static VOID
_InitInterrupt_8192EU(
	IN  PADAPTER Adapter
	)
{
	HAL_DATA_TYPE	*pHalData	= GET_HAL_DATA(Adapter);

	/*HISR write one to clear*/
	rtw_write32(Adapter, REG_HISR0_8192E, 0xFFFFFFFF);
	rtw_write32(Adapter, REG_HISR1_8192E, 0xFFFFFFFF);

	// HIMR
	rtw_write32(Adapter, REG_HIMR0_8192E, pHalData->IntrMask[0]&0xFFFFFFFF);
	rtw_write32(Adapter, REG_HIMR1_8192E, pHalData->IntrMask[1]&0xFFFFFFFF);
}


static VOID
_InitQueueReservedPage_8192EUsb(
	IN  PADAPTER Adapter
	)
{
	_InitQueueReservedPage_8192E(Adapter);	
}

static VOID
_InitHardwareDropIncorrectBulkOut_8192E(
	IN  PADAPTER Adapter
	)
{
#ifdef ENABLE_USB_DROP_INCORRECT_OUT
	u32	value32 = rtw_read32(Adapter, REG_TXDMA_OFFSET_CHK);
	value32 |= DROP_DATA_EN;
	rtw_write32(Adapter, REG_TXDMA_OFFSET_CHK, value32);
#endif
}



#ifdef CONFIG_LED
static void _InitHWLed(PADAPTER Adapter)
{
	struct led_priv *pledpriv = &(Adapter->ledpriv);
	
	if( pledpriv->LedStrategy != HW_LED)
		return;

	rtw_write8(Adapter,REG_LEDCFG1,0x02);
// HW led control
// to do .... 
//must consider cases of antenna diversity/ commbo card/solo card/mini card

}
#endif //CONFIG_LED


static VOID
_init_UsbBusSetting_8192EU(
	IN  PADAPTER Adapter
	)
{
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	u8 usb_bus_setting = 0;
	usb_bus_setting = rtw_read8(Adapter,REG_RXDMA_8192E);
	usb_bus_setting = usb_bus_setting| BIT_DMA_MODE;
	usb_bus_setting = usb_bus_setting|BIT(3)|BIT(2);//Burst number in dma mode,DD suggest 0x11		

	//IS_SUPER_SPEED_USB(Adapter) //for USB 3.0
	
	if(IS_HIGH_SPEED_USB(Adapter))
	{			
		rtw_write8(Adapter,REG_RXDMA_8192E,((usb_bus_setting|BIT(4))&(~BIT(5))));						
	}
	else if(IS_FULL_SPEED_USB(Adapter))
	{
		rtw_write8(Adapter,REG_RXDMA_8192E,((usb_bus_setting|BIT(5))&(~BIT(4))));
	}	

}


/*-----------------------------------------------------------------------------
 * Function:	usb_AggSettingTxUpdate()
 *
 * Overview:	Seperate TX/RX parameters update independent for TP detection and 
 *			dynamic TX/RX aggreagtion parameters update.
 *
 * Input:			PADAPTER
 *
 * Output/Return:	NONE
 *
 * Revised History:
 *	When		Who		Remark
 *	12/10/2010	MHC		Seperate to smaller function.
 *
 *---------------------------------------------------------------------------*/
static VOID
usb_AggSettingTxUpdate_8192EU(
	IN	PADAPTER			Adapter
	)
{
#ifdef CONFIG_USB_TX_AGGREGATION
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	u32			value32;

	if(Adapter->registrypriv.wifi_spec)
		pHalData->UsbTxAggMode = _FALSE;

	if(pHalData->UsbTxAggMode){
		value32 = rtw_read32(Adapter, REG_DWBCN0_CTRL_8192E);
		value32 = value32 & ~(BLK_DESC_NUM_MASK << BLK_DESC_NUM_SHIFT);
		value32 |= ((pHalData->UsbTxAggDescNum & BLK_DESC_NUM_MASK) << BLK_DESC_NUM_SHIFT);
		
		rtw_write32(Adapter, REG_DWBCN0_CTRL_8192E, value32);
		rtw_write8(Adapter, REG_DWBCN1_CTRL_8192E, pHalData->UsbTxAggDescNum<<1);
	}
	
#endif
}	// usb_AggSettingTxUpdate


/*-----------------------------------------------------------------------------
 * Function:	usb_AggSettingRxUpdate()
 *
 * Overview:	Seperate TX/RX parameters update independent for TP detection and 
 *			dynamic TX/RX aggreagtion parameters update.
 *
 * Input:			PADAPTER
 *
 * Output/Return:	NONE
 *
 * Revised History:
 *	When		Who		Remark
 *	12/10/2010	MHC		Seperate to smaller function.
 *
 *---------------------------------------------------------------------------*/

static VOID
usb_AggSettingRxUpdate_8192EU(
	IN	PADAPTER			Adapter
	)
{
#ifdef CONFIG_USB_RX_AGGREGATION
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	u8			usb_agg_setting;
	u32			usb_agg_th;
	
	usb_agg_setting = rtw_read8(Adapter, REG_TRXDMA_CTRL);
	rtw_write8(Adapter, REG_TRXDMA_CTRL, usb_agg_setting|RXDMA_AGG_EN);

	usb_agg_th = (pHalData->RegAcUsbDmaSize&0x0F) | (pHalData->RegAcUsbDmaTime<<8);
	
	switch(pHalData->UsbRxAggMode)
	{
		case USB_RX_AGG_DMA:					
			{						
				usb_agg_th |= BIT_USB_RXDMA_AGG_EN;				
			}
			break;
		case USB_RX_AGG_USB:
		case USB_RX_AGG_MIX:
			break;
		case USB_RX_AGG_DISABLE:
		default:
			// TODO: 
			break;
	}

	rtw_write32(Adapter, REG_RXDMA_AGG_PG_TH, usb_agg_th); 
#endif
	// 201/12/10 MH Add for USB agg mode dynamic switch.
	pHalData->UsbRxHighSpeedMode = _FALSE;	

}	// usb_AggSettingRxUpdate

static VOID
_init_UsbAggregationSetting_8192EU(
	IN  PADAPTER Adapter
	)
{
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);

	// Tx aggregation setting
	usb_AggSettingTxUpdate_8192EU(Adapter);

	// Rx aggregation setting
	usb_AggSettingRxUpdate_8192EU(Adapter);
}

/*-----------------------------------------------------------------------------
 * Function:	USB_AggModeSwitch()
 *
 * Overview:	When RX traffic is more than 40M, we need to adjust some parameters to increase
 *			RX speed by increasing batch indication size. This will decrease TCP ACK speed, we
 *			need to monitor the influence of FTP/network share.
 *			For TX mode, we are still ubder investigation.
 *
 * Input:		PADAPTER
 *
 * Output:		NONE
 *
 * Return:		NONE
 *
 * Revised History:
 *	When		Who		Remark
 *	12/10/2010	MHC		Create Version 0.  
 *
 *---------------------------------------------------------------------------*/
VOID
USB_AggModeSwitch(
	IN	PADAPTER			Adapter
	)
{
#if 0
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	PMGNT_INFO		pMgntInfo = &(Adapter->MgntInfo);

	//pHalData->UsbRxHighSpeedMode = FALSE;
	// How to measure the RX speed? We assume that when traffic is more than 
	if (pMgntInfo->bRegAggDMEnable == FALSE)
	{
		return;	// Inf not support.
	}
	
	
	if (pMgntInfo->LinkDetectInfo.bHigherBusyRxTraffic == TRUE && 
		pHalData->UsbRxHighSpeedMode == FALSE)
	{
		pHalData->UsbRxHighSpeedMode = TRUE;
		RT_TRACE(COMP_INIT, DBG_LOUD, ("UsbAggModeSwitchCheck to HIGH\n"));
	}
	else if (pMgntInfo->LinkDetectInfo.bHigherBusyRxTraffic == FALSE && 
		pHalData->UsbRxHighSpeedMode == TRUE)
	{
		pHalData->UsbRxHighSpeedMode = FALSE;
		RT_TRACE(COMP_INIT, DBG_LOUD, ("UsbAggModeSwitchCheck to LOW\n"));
	}
	else
	{
		return; 
	}
	

#if USB_RX_AGGREGATION_92C
	if (pHalData->UsbRxHighSpeedMode == TRUE)	
	{
		// 2010/12/10 MH The parameter is tested by SD1 engineer and SD3 channel emulator.
		// USB mode
#if (RT_PLATFORM == PLATFORM_LINUX)
		if (pMgntInfo->LinkDetectInfo.bTxBusyTraffic)
		{
			pHalData->RxAggBlockCount	= 16;
			pHalData->RxAggBlockTimeout	= 7;
		}
		else
#endif
		{
			pHalData->RxAggBlockCount	= 40;
			pHalData->RxAggBlockTimeout	= 5;
		}
		// Mix mode
		pHalData->RxAggPageCount	= 72;
		pHalData->RxAggPageTimeout	= 6;		
	}
	else
	{
		// USB mode
		pHalData->RxAggBlockCount	= pMgntInfo->RegRxAggBlockCount;
		pHalData->RxAggBlockTimeout	= pMgntInfo->RegRxAggBlockTimeout;	
		// Mix mode
		pHalData->RxAggPageCount		= pMgntInfo->RegRxAggPageCount;
		pHalData->RxAggPageTimeout	= pMgntInfo->RegRxAggPageTimeout;	
	}

	if (pHalData->RxAggBlockCount > MAX_RX_AGG_BLKCNT)
		pHalData->RxAggBlockCount = MAX_RX_AGG_BLKCNT;
#if (OS_WIN_FROM_VISTA(OS_VERSION)) || (RT_PLATFORM == PLATFORM_LINUX)	// do not support WINXP to prevent usbehci.sys BSOD
	if (IS_WIRELESS_MODE_N_24G(Adapter) || IS_WIRELESS_MODE_N_5G(Adapter))
	{
		//
		// 2010/12/24 MH According to V1012 QC IOT test, XP BSOD happen when running chariot test
		// with the aggregation dynamic change!! We need to disable the function to prevent it is broken
		// in usbehci.sys.
		//
		usb_AggSettingRxUpdate_8188E(Adapter);

		// 2010/12/27 MH According to designer's suggstion, we can only modify Timeout value. Otheriwse
		// there might many HW incorrect behavior, the XP BSOD at usbehci.sys may be relative to the 
		// issue. Base on the newest test, we can not enable block cnt > 30, otherwise XP usbehci.sys may
		// BSOD.
	}
#endif
	
#endif
#endif
}	// USB_AggModeSwitch

static VOID _RfPowerSave(
	IN	PADAPTER		Adapter
	)
{
#if 0
	HAL_DATA_TYPE	*pHalData	= GET_HAL_DATA(Adapter);
	PMGNT_INFO		pMgntInfo	= &(Adapter->MgntInfo);
	u1Byte			eRFPath;

#if (DISABLE_BB_RF)
	return;
#endif

	if(pMgntInfo->RegRfOff == TRUE){ // User disable RF via registry.
		RT_TRACE((COMP_INIT|COMP_RF), DBG_LOUD, ("InitializeAdapter8192CUsb(): Turn off RF for RegRfOff.\n"));
		MgntActSet_RF_State(Adapter, eRfOff, RF_CHANGE_BY_SW);
		// Those action will be discard in MgntActSet_RF_State because off the same state
		for(eRFPath = 0; eRFPath <pHalData->NumTotalRFPath; eRFPath++)
			PHY_SetRFReg(Adapter, eRFPath, 0x4, 0xC00, 0x0);
	}
	else if(pMgntInfo->RfOffReason > RF_CHANGE_BY_PS){ // H/W or S/W RF OFF before sleep.
		RT_TRACE((COMP_INIT|COMP_RF), DBG_LOUD, ("InitializeAdapter8192CUsb(): Turn off RF for RfOffReason(%ld).\n", pMgntInfo->RfOffReason));
		MgntActSet_RF_State(Adapter, eRfOff, pMgntInfo->RfOffReason);
	}
	else{
		pHalData->eRFPowerState = eRfOn;
		pMgntInfo->RfOffReason = 0; 
		if(Adapter->bInSetPower || Adapter->bResetInProgress)
			PlatformUsbEnableInPipes(Adapter);
		RT_TRACE((COMP_INIT|COMP_RF), DBG_LOUD, ("InitializeAdapter8192CUsb(): RF is on.\n"));
	}
#endif
}

enum {
	Antenna_Lfet = 1,
	Antenna_Right = 2,	
};

static VOID
_InitAntenna_Selection_8192E(IN	PADAPTER Adapter)
{

	HAL_DATA_TYPE	*pHalData	= GET_HAL_DATA(Adapter);

	if(pHalData->AntDivCfg==0)
		return;
/*
	DBG_8192C("==>  %s ....\n",__FUNCTION__);		

	rtw_write8(Adapter, REG_LEDCFG2, 0x82);

	PHY_SetBBReg(Adapter, rFPGA0_XAB_RFParameter, BIT13, 0x01);
		
	if(PHY_QueryBBReg(Adapter, rFPGA0_XA_RFInterfaceOE, 0x300) == MAIN_ANT)
		pHalData->CurAntenna = MAIN_ANT;
	else
		pHalData->CurAntenna = AUX_ANT;
	DBG_8192C("%s,Cur_ant:(%x)%s\n",__FUNCTION__,pHalData->CurAntenna,(pHalData->CurAntenna == MAIN_ANT)?"MAIN_ANT":"AUX_ANT");
*/

}

//
// 2010/08/26 MH Add for selective suspend mode check.
// If Efuse 0x0e bit1 is not enabled, we can not support selective suspend for Minicard and
// slim card.
//
static VOID
HalDetectSelectiveSuspendMode(
	IN PADAPTER				Adapter
	)
{
#if 0
	u8	tmpvalue;
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	struct dvobj_priv	*pdvobjpriv = adapter_to_dvobj(Adapter);

	// If support HW radio detect, we need to enable WOL ability, otherwise, we 
	// can not use FW to notify host the power state switch.
	
	EFUSE_ShadowRead(Adapter, 1, EEPROM_USB_OPTIONAL1, (u32 *)&tmpvalue);

	DBG_8192C("HalDetectSelectiveSuspendMode(): SS ");
	if(tmpvalue & BIT1)
	{
		DBG_8192C("Enable\n");
	}
	else
	{
		DBG_8192C("Disable\n");
		pdvobjpriv->RegUsbSS = _FALSE;
	}

	// 2010/09/01 MH According to Dongle Selective Suspend INF. We can switch SS mode.
	if (pdvobjpriv->RegUsbSS && !SUPPORT_HW_RADIO_DETECT(pHalData))
	{
		//PMGNT_INFO				pMgntInfo = &(Adapter->MgntInfo);

		//if (!pMgntInfo->bRegDongleSS)	
		//{
		//	RT_TRACE(COMP_INIT, DBG_LOUD, ("Dongle disable SS\n"));
			pdvobjpriv->RegUsbSS = _FALSE;
		//}
	}
#endif
}	// HalDetectSelectiveSuspendMode

#if 0
/*-----------------------------------------------------------------------------
 * Function:	HwSuspendModeEnable92Cu()
 *
 * Overview:	HW suspend mode switch.
 *
 * Input:		NONE
 *
 * Output:	NONE
 *
 * Return:	NONE
 *
 * Revised History:
 *	When		Who		Remark
 *	08/23/2010	MHC		HW suspend mode switch test..
 *---------------------------------------------------------------------------*/
static VOID 
HwSuspendModeEnable_8192EU(
	IN	PADAPTER	pAdapter,
	IN	u8			Type
	)
{
	//PRT_USB_DEVICE 		pDevice = GET_RT_USB_DEVICE(pAdapter);
	u16	reg = rtw_read16(pAdapter, REG_GPIO_MUXCFG);	

	//if (!pDevice->RegUsbSS)
	{
		return;
	}

	//
	// 2010/08/23 MH According to Alfred's suggestion, we need to to prevent HW
	// to enter suspend mode automatically. Otherwise, it will shut down major power 
	// domain and 8051 will stop. When we try to enter selective suspend mode, we
	// need to prevent HW to enter D2 mode aumotmatically. Another way, Host will
	// issue a S10 signal to power domain. Then it will cleat SIC setting(from Yngli).
	// We need to enable HW suspend mode when enter S3/S4 or disable. We need 
	// to disable HW suspend mode for IPS/radio_off.
	//
	//RT_TRACE(COMP_RF, DBG_LOUD, ("HwSuspendModeEnable92Cu = %d\n", Type));
	if (Type == _FALSE)
	{
		reg |= BIT14;
		//RT_TRACE(COMP_RF, DBG_LOUD, ("REG_GPIO_MUXCFG = %x\n", reg));
		rtw_write16(pAdapter, REG_GPIO_MUXCFG, reg);
		reg |= BIT12;
		//RT_TRACE(COMP_RF, DBG_LOUD, ("REG_GPIO_MUXCFG = %x\n", reg));
		rtw_write16(pAdapter, REG_GPIO_MUXCFG, reg);
	}
	else
	{
		reg &= (~BIT12);
		rtw_write16(pAdapter, REG_GPIO_MUXCFG, reg);
		reg &= (~BIT14);
		rtw_write16(pAdapter, REG_GPIO_MUXCFG, reg);
	}
	
}	// HwSuspendModeEnable92Cu
#endif

rt_rf_power_state RfOnOffDetect(IN	PADAPTER pAdapter )
{
	struct pwrctrl_priv *pwrctl = adapter_to_pwrctl(pAdapter);
	HAL_DATA_TYPE		*pHalData = GET_HAL_DATA(pAdapter);
	u8	val8;
	rt_rf_power_state rfpowerstate = rf_off;

	if(pwrctl->bHWPowerdown)
	{
		val8 = rtw_read8(pAdapter, REG_HSISR);
		DBG_8192C("pwrdown, 0x5c(BIT7)=%02x\n", val8);
		rfpowerstate = (val8 & BIT7) ? rf_off: rf_on;				
	}
	else // rf on/off
	{
		rtw_write8(	pAdapter, REG_MAC_PINMUX_CFG,rtw_read8(pAdapter, REG_MAC_PINMUX_CFG)&~(BIT3));
		val8 = rtw_read8(pAdapter, REG_GPIO_IO_SEL);
		DBG_8192C("GPIO_IN=%02x\n", val8);
		rfpowerstate = (val8 & BIT3) ? rf_on : rf_off;	
	}
	return rfpowerstate;
}	// HalDetectPwrDownMode

void _ps_open_RF(_adapter *padapter) {
	//here call with bRegSSPwrLvl 1, bRegSSPwrLvl 2 needs to be verified
	//phy_SsPwrSwitch92CU(padapter, rf_on, 1);
}

void _ps_close_RF(_adapter *padapter){
	//here call with bRegSSPwrLvl 1, bRegSSPwrLvl 2 needs to be verified
	//phy_SsPwrSwitch92CU(padapter, rf_off, 1);
}
//page added for usb2 phy reg access. 20120514
VOID WriteUSB2PHYReg_8192EU(PADAPTER Adapter, u8 Offset, u8 Value)
{	
	Offset -= 0x20;
	rtw_write8(Adapter, 0xFE41, Value);
	rtw_write8(Adapter, 0xFE40, Offset);
	rtw_write8(Adapter, 0xFE42, 0x81);
}

u1Byte ReadUSB2PHYReg_8192EU(PADAPTER Adapter, u8 Offset)
{	
	u8 value;
	rtw_write8(Adapter, 0xFE40, Offset);
	rtw_write8(Adapter, 0xFE42, 0x81);
	value = rtw_read8(Adapter, 0xFE43);

	return value;
}
u32 rtl8192eu_hal_init(PADAPTER Adapter)
{
	u8	value8 = 0;
	u16  value16;
	u8	txpktbuf_bndy;
	u32	status = _SUCCESS;
	HAL_DATA_TYPE		*pHalData = GET_HAL_DATA(Adapter);
	struct pwrctrl_priv		*pwrctrlpriv = adapter_to_pwrctl(Adapter);
	struct registry_priv	*pregistrypriv = &Adapter->registrypriv;
	
	rt_rf_power_state		eRfPowerStateToSet;


	u32 init_start_time = rtw_get_current_time();


#ifdef DBG_HAL_INIT_PROFILING

	enum HAL_INIT_STAGES {
		HAL_INIT_STAGES_BEGIN = 0,
		HAL_INIT_STAGES_INIT_PW_ON,
		HAL_INIT_STAGES_MISC01,
		HAL_INIT_STAGES_DOWNLOAD_FW,
		HAL_INIT_STAGES_MAC,
		HAL_INIT_STAGES_BB,
		HAL_INIT_STAGES_RF,	
		HAL_INIT_STAGES_EFUSE_PATCH,
		HAL_INIT_STAGES_INIT_LLTT,	
		
		HAL_INIT_STAGES_MISC02,
		HAL_INIT_STAGES_TURN_ON_BLOCK,
		HAL_INIT_STAGES_INIT_SECURITY,
		HAL_INIT_STAGES_MISC11,
		HAL_INIT_STAGES_INIT_HAL_DM,
		//HAL_INIT_STAGES_RF_PS,
		HAL_INIT_STAGES_IQK,
		HAL_INIT_STAGES_PW_TRACK,
		HAL_INIT_STAGES_LCK,
		HAL_INIT_STAGES_MISC21,
		//HAL_INIT_STAGES_INIT_PABIAS,
		#ifdef CONFIG_BT_COEXIST
		HAL_INIT_STAGES_BT_COEXIST,
		#endif
		//HAL_INIT_STAGES_ANTENNA_SEL,
		HAL_INIT_STAGES_MISC31,
		HAL_INIT_STAGES_END,
		HAL_INIT_STAGES_NUM
	};

	char * hal_init_stages_str[] = {
		"HAL_INIT_STAGES_BEGIN",
		"HAL_INIT_STAGES_INIT_PW_ON",
		"HAL_INIT_STAGES_MISC01",
		"HAL_INIT_STAGES_DOWNLOAD_FW",		
		"HAL_INIT_STAGES_MAC",		
		"HAL_INIT_STAGES_BB",
		"HAL_INIT_STAGES_RF",
		"HAL_INIT_STAGES_EFUSE_PATCH",
		"HAL_INIT_STAGES_INIT_LLTT",
		"HAL_INIT_STAGES_MISC02",		
		"HAL_INIT_STAGES_TURN_ON_BLOCK",
		"HAL_INIT_STAGES_INIT_SECURITY",
		"HAL_INIT_STAGES_MISC11",
		"HAL_INIT_STAGES_INIT_HAL_DM",
		//"HAL_INIT_STAGES_RF_PS",
		"HAL_INIT_STAGES_IQK",
		"HAL_INIT_STAGES_PW_TRACK",
		"HAL_INIT_STAGES_LCK",
		"HAL_INIT_STAGES_MISC21",
		#ifdef CONFIG_BT_COEXIST
		"HAL_INIT_STAGES_BT_COEXIST",
		#endif
		//"HAL_INIT_STAGES_ANTENNA_SEL",
		"HAL_INIT_STAGES_MISC31",
		"HAL_INIT_STAGES_END",
	};

	int hal_init_profiling_i;
	u32 hal_init_stages_timestamp[HAL_INIT_STAGES_NUM]; //used to record the time of each stage's starting point

	for(hal_init_profiling_i=0;hal_init_profiling_i<HAL_INIT_STAGES_NUM;hal_init_profiling_i++)
		hal_init_stages_timestamp[hal_init_profiling_i]=0;

	#define HAL_INIT_PROFILE_TAG(stage) hal_init_stages_timestamp[(stage)]=rtw_get_current_time();
#else
	#define HAL_INIT_PROFILE_TAG(stage) do {} while(0)
#endif //DBG_HAL_INIT_PROFILING



_func_enter_;
	
HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_BEGIN);
/*
	if(0)
	{
		WriteUSB2PHYReg_8192EU(Adapter, 0xE1, ReadUSB2PHYReg_8192EU(Adapter, 0xE1)&0x7f);
		WriteUSB2PHYReg_8192EU(Adapter, 0xE2, ReadUSB2PHYReg_8192EU(Adapter, 0xE2)&0x0f);
		delay_us(50);
		WriteUSB2PHYReg_8192EU(Adapter, 0xE1, ReadUSB2PHYReg_8192EU(Adapter, 0xE1)|0x80);
		WriteUSB2PHYReg_8192EU(Adapter, 0xE2, ReadUSB2PHYReg_8192EU(Adapter, 0xE1)|0x90);
	}
*/	

#ifdef CONFIG_WOWLAN
	
	pwrctrlpriv->wowlan_wake_reason = rtw_read8(Adapter, REG_WOWLAN_WAKE_REASON);
	DBG_8192C("%s wowlan_wake_reason: 0x%02x\n", 
				__func__, pwrctrlpriv->wowlan_wake_reason);

	if(rtw_read8(Adapter, REG_MCUFWDL)&BIT7){ /*&&
		(pwrctrlpriv->wowlan_wake_reason & FWDecisionDisconnect)) {*/
		u8 reg_val=0;
		DBG_8192C("+Reset Entry+\n");
		rtw_write8(Adapter, REG_MCUFWDL, 0x00);
		_8051Reset8192E(Adapter);
		//reset BB
		reg_val = rtw_read8(Adapter, REG_SYS_FUNC_EN);
		reg_val &= ~(BIT(0) | BIT(1));
		rtw_write8(Adapter, REG_SYS_FUNC_EN, reg_val);
		//reset RF
		rtw_write8(Adapter, REG_RF_CTRL, 0);
		//reset TRX path
		rtw_write16(Adapter, REG_CR, 0);
		//reset MAC, Digital Core
		reg_val = rtw_read8(Adapter, REG_SYS_FUNC_EN+1);
		reg_val &= ~(BIT(4) | BIT(7));
		rtw_write8(Adapter, REG_SYS_FUNC_EN+1, reg_val);
		reg_val = rtw_read8(Adapter, REG_SYS_FUNC_EN+1);
		reg_val |= BIT(4) | BIT(7);
		rtw_write8(Adapter, REG_SYS_FUNC_EN+1, reg_val);
		DBG_8192C("-Reset Entry-\n");
	}
#endif //CONFIG_WOWLAN


	if(pwrctrlpriv->bkeepfwalive)
	{
		_ps_open_RF(Adapter);

		if(pHalData->odmpriv.RFCalibrateInfo.bIQKInitialized){
//			PHY_IQCalibrate(padapter, _TRUE);		
		}
		else
		{
//			PHY_IQCalibrate(padapter, _FALSE);			
			pHalData->odmpriv.RFCalibrateInfo.bIQKInitialized = _TRUE;
		}

//		dm_CheckTXPowerTracking(padapter);
//		PHY_LCCalibrate(padapter);
		ODM_TXPowerTrackingCheck(&pHalData->odmpriv );
		//PHY_LCCalibrate_8188E(Adapter);

		goto exit;
	}



HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_INIT_PW_ON);
	status = _InitPowerOn_8192EU(Adapter);
	if(status == _FAIL){
		RT_TRACE(_module_hci_hal_init_c_, _drv_err_, ("Failed to init power on!\n"));
		goto exit;
	}

	txpktbuf_bndy = TX_PAGE_BOUNDARY_8192E;
	
HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_MISC01);
	_InitQueueReservedPage_8192EUsb(Adapter);	
	_InitQueuePriority_8192E(Adapter);		
	_InitPageBoundary_8192E(Adapter);	

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_DOWNLOAD_FW);
#if (MP_DRIVER == 1)
	if (Adapter->registrypriv.mp_mode == 1)
	{
		_InitRxSetting_8192E(Adapter);
	}
	else
#endif  //MP_DRIVER == 1
	{
		status = FirmwareDownload8192E(Adapter, _FALSE);
		if (status != _SUCCESS) {
			DBG_871X("%s: Download Firmware failed!!\n", __FUNCTION__);
			Adapter->bFWReady = _FALSE;
			pHalData->fw_ractrl = _FALSE;
			return status;
		} else {
			RT_TRACE(_module_hci_hal_init_c_, _drv_info_, ("Initializepadapter8192CSdio(): Download Firmware Success!!\n"));
			Adapter->bFWReady = _TRUE;
			pHalData->fw_ractrl = _TRUE;
		}

	}
	InitializeFirmwareVars8192E(Adapter);

	if(pwrctrlpriv->reg_rfoff == _TRUE){
		pwrctrlpriv->rf_pwrstate = rf_off;
	}

	// Save target channel	
	pHalData->CurrentChannel = 6;//default set to 6

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_MAC);
#if (HAL_MAC_ENABLE == 1)
	status = PHY_MACConfig8192E(Adapter);
	if(status == _FAIL)
	{
		goto exit;
	}
#endif

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_BB);
#if (HAL_BB_ENABLE == 1)
	status = PHY_BBConfig8192E(Adapter);
	if(status == _FAIL)
	{
		goto exit;
	}
#endif

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_RF);
#if (HAL_RF_ENABLE == 1)
	status = PHY_RFConfig8192E(Adapter);	
	if(status == _FAIL)
	{
		goto exit;
	}	


HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_EFUSE_PATCH);
	
	_InitTxBufferBoundary_8192E(Adapter, txpktbuf_bndy);	

	
	status =  InitLLTTable8192E(Adapter, txpktbuf_bndy);
	if(status == _FAIL){
		RT_TRACE(_module_hci_hal_init_c_, _drv_err_, ("Failed to init LLT table\n"));
		goto exit;
	}

	_InitHardwareDropIncorrectBulkOut_8192E(Adapter);

	if(pHalData->bRDGEnable){
		_InitRDGSetting_8192E(Adapter);	
	}

#ifdef CONFIG_TX_EARLY_MODE

	if(pHalData->AMPDUBurstMode)
	{
		RT_TRACE(_module_hci_hal_init_c_, _drv_info_,("EarlyMode Enabled!!!\n"));

		value8 = rtw_read8(Adapter, REG_EARLY_MODE_CONTROL_8192E);
#if RTL8192E_EARLY_MODE_PKT_NUM_10 == 1
		value8 = value8|0x1f;
#else
		value8 = value8|0xf;
#endif
		rtw_write8(Adapter, REG_EARLY_MODE_CONTROL_8192E, value8);

		rtw_write8(Adapter, REG_EARLY_MODE_CONTROL_8192E+3, 0x80);

		value8 = rtw_read8(Adapter, REG_TCR+1);
		value8 = value8|0x40;
		rtw_write8(Adapter,REG_TCR+1, value8);
	}
	else
	{
		//rtw_write8(Adapter, REG_EARLY_MODE_CONTROL, 0);
	}	
#endif //CONFIG_TX_EARLY_MODE

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_MISC02);
	// Get Rx PHY status in order to report RSSI and others.
	_InitDriverInfoSize_8192E(Adapter, DRVINFO_SZ);

	_InitInterrupt_8192EU(Adapter);
	
	_InitID_8192E(Adapter);//set mac_address
	
	_InitNetworkType_8192E(Adapter);//set msr	
	_InitWMACSetting_8192E(Adapter);
	_InitAdaptiveCtrl_8192E(Adapter);
	_InitRateFallback_8192E(Adapter);
	_InitEDCA_8192E(Adapter);
	_InitRetryFunction_8192E(Adapter);
	_init_UsbBusSetting_8192EU(Adapter);	
	_init_UsbAggregationSetting_8192EU(Adapter);
		
	_InitBeaconParameters_8192E(Adapter);
	_InitBeaconMaxError_8192E(Adapter, _TRUE);

	_InitBurstPktLen_8192EU(Adapter);  //added by page. 20110919

	//
	// Init CR MACTXEN, MACRXEN after setting RxFF boundary REG_TRXFF_BNDY to patch
	// Hw bug which Hw initials RxFF boundry size to a value which is larger than the real Rx buffer size in 88E. 
	// 2011.08.05. by tynli.
	//
	value8 = rtw_read8(Adapter, REG_CR);
	rtw_write8(Adapter, REG_CR, (value8|MACTXEN|MACRXEN));

#ifdef CONFIG_CHECK_AC_LIFETIME
	// Enable lifetime check for the four ACs
	rtw_write8(Adapter, REG_LIFETIME_CTRL, 0x0F);
#endif	// CONFIG_CHECK_AC_LIFETIME

#if defined(CONFIG_CONCURRENT_MODE) || defined(CONFIG_TX_MCAST2UNI)
#ifdef CONFIG_TX_MCAST2UNI
	rtw_write16(Adapter, REG_PKT_VO_VI_LIFE_TIME, 0x0400);	// unit: 256us. 256ms
	rtw_write16(Adapter, REG_PKT_BE_BK_LIFE_TIME, 0x0400);	// unit: 256us. 256ms
#else	// CONFIG_TX_MCAST2UNI
	rtw_write16(Adapter, REG_PKT_VO_VI_LIFE_TIME, 0x3000);	// unit: 256us. 3s
	rtw_write16(Adapter, REG_PKT_BE_BK_LIFE_TIME, 0x3000);	// unit: 256us. 3s
#endif	// CONFIG_TX_MCAST2UNI
#endif	// CONFIG_CONCURRENT_MODE || CONFIG_TX_MCAST2UNI
	

#ifdef CONFIG_LED
	_InitHWLed(Adapter);
#endif //CONFIG_LED

	_BBTurnOnBlock_8192E(Adapter);
#endif

	//
	// Joseph Note: Keep RfRegChnlVal for later use.
	//
	pHalData->RfRegChnlVal[0] = PHY_QueryRFReg(Adapter, 0, RF_CHNLBW, bRFRegOffsetMask);
	pHalData->RfRegChnlVal[1] = PHY_QueryRFReg(Adapter, 1, RF_CHNLBW, bRFRegOffsetMask);
	

	rtw_hal_set_chnl_bw(Adapter, Adapter->registrypriv.channel, 
		CHANNEL_WIDTH_20, HAL_PRIME_CHNL_OFFSET_DONT_CARE, HAL_PRIME_CHNL_OFFSET_DONT_CARE);

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_TURN_ON_BLOCK);

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_INIT_SECURITY);
	invalidate_cam_all(Adapter);

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_MISC11);
	_InitAntenna_Selection_8192E(Adapter);

	// HW SEQ CTRL
	//set 0x0 to 0xFF by tynli. Default enable HW SEQ NUM.
	rtw_write8(Adapter,REG_HWSEQ_CTRL, 0xFF); 
	
	// 
	// Disable BAR, suggested by Scott
	// 2010.04.09 add by hpfan
	//
	rtw_write32(Adapter, REG_BAR_MODE_CTRL, 0x0201ffff);
	PHY_SetRFEReg_8192E(Adapter);

	if(pregistrypriv->wifi_spec){
		rtw_write16(Adapter,REG_FAST_EDCA_CTRL ,0);

		//Nav limit , suggest by SD1-Pisa,disable NAV_UPPER function when wifi_spec=1 for Test item: 5.2.3
		rtw_write8(Adapter, REG_NAV_UPPER, 0x0);
	}

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_INIT_HAL_DM);
	rtl8192e_InitHalDm(Adapter);
	
#if (MP_DRIVER == 1)
	if (Adapter->registrypriv.mp_mode == 1)
	{
		Adapter->mppriv.channel = pHalData->CurrentChannel;
		MPT_InitializeAdapter(Adapter, Adapter->mppriv.channel);
	}
	else	
#endif  //#if (MP_DRIVER == 1)
	{
	//
	// 2010/08/11 MH Merge from 8192SE for Minicard init. We need to confirm current radio status
	// and then decide to enable RF or not.!!!??? For Selective suspend mode. We may not 
	// call init_adapter. May cause some problem??
	//
	// Fix the bug that Hw/Sw radio off before S3/S4, the RF off action will not be executed 
	// in MgntActSet_RF_State() after wake up, because the value of pHalData->eRFPowerState 
	// is the same as eRfOff, we should change it to eRfOn after we config RF parameters.
	// Added by tynli. 2010.03.30.
	pwrctrlpriv->rf_pwrstate = rf_on;


	//0x4c6[3] 1: RTS BW = Data BW
	//0: RTS BW depends on CCA / secondary CCA result.
	rtw_write8(Adapter, REG_QUEUE_CTRL, rtw_read8(Adapter, REG_QUEUE_CTRL)&0xF7);

	// enable Tx report.
	//rtw_write8(Adapter,  REG_FWHW_TXQ_CTRL+1, 0x0F);

	// Suggested by SD1 pisa. Added by tynli. 2011.10.21.
	//rtw_write8(Adapter, REG_EARLY_MODE_CONTROL_8192E+3, 0x01);//Pretx_en, for WEP/TKIP SEC

	//tynli_test_tx_report.
	//rtw_write16(Adapter, REG_TX_RPT_TIME, 0x3DF0);

	// Reset USB mode switch setting	
	rtw_write8(Adapter, REG_ACLK_MON, 0x0);
	
	//RT_TRACE(COMP_INIT, DBG_TRACE, ("InitializeAdapter8188EUsb() <====\n"));
	
HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_IQK);	
	if(pwrctrlpriv->rf_pwrstate == rf_on)
	{
		pHalData->odmpriv.RFCalibrateInfo.bNeedIQK = _TRUE;
		if(pHalData->odmpriv.RFCalibrateInfo.bIQKInitialized){
			PHY_IQCalibrate_8192E(Adapter,_TRUE);
		}
		else
		{
			PHY_IQCalibrate_8192E(Adapter,_FALSE);
			pHalData->odmpriv.RFCalibrateInfo.bIQKInitialized = _TRUE;
		}
		
HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_PW_TRACK);
		
		ODM_TXPowerTrackingCheck(&pHalData->odmpriv );
		

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_LCK);
		//PHY_LCCalibrate_8192E((GET_HAL_DATA(Adapter)->odmpriv));		
	}
}
#ifdef CONFIG_HIGH_CHAN_SUPER_CALIBRATION
	rtw_hal_set_chnl_bw(Adapter, 13, 
		CHANNEL_WIDTH_20, HAL_PRIME_CHNL_OFFSET_DONT_CARE, HAL_PRIME_CHNL_OFFSET_DONT_CARE); 
	PHY_SpurCalibration_8192E(Adapter);
	rtw_hal_set_chnl_bw(Adapter, Adapter->registrypriv.channel, 
		CHANNEL_WIDTH_20, HAL_PRIME_CHNL_OFFSET_DONT_CARE, HAL_PRIME_CHNL_OFFSET_DONT_CARE);
#endif


HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_MISC21);


//HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_INIT_PABIAS);
//	_InitPABias(Adapter);

#ifdef CONFIG_BT_COEXIST
	HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_BT_COEXIST);

	if (pHalData->EEPROMBluetoothCoexist == 1) {
		/* YiWei 20140624 , Fix 8192eu mailbox BT info no response issue reduce I2C clock rate to 156KHz (default 1.25Mhz) */
		rtw_write8(Adapter, rPMAC_TxPacketNum, rtw_read8(Adapter, rPMAC_TxPacketNum)|0x7);

		/* Init BT hw config.*/
		rtw_btcoex_HAL_Initialize(Adapter, _FALSE);      
	}
	/*else
	{
		 // In combo card run wifi only , must setting some hardware reg.
		rtl8192e_combo_card_WifiOnlyHwInit(Adapter);
	}*/
#endif

	// 2010/08/23 MH According to Alfred's suggestion, we need to to prevent HW enter
	// suspend mode automatically.
	//HwSuspendModeEnable92Cu(Adapter, _FALSE);

HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_MISC31);

	rtw_write8(Adapter, REG_USB_HRPWM, 0);
#ifdef CONFIG_XMIT_ACK
	//ack for xmit mgmt frames.
	rtw_write32(Adapter, REG_FWHW_TXQ_CTRL, rtw_read32(Adapter, REG_FWHW_TXQ_CTRL)|BIT(12));
#endif //CONFIG_XMIT_ACK
	//Fixed LDPC rx hang issue.
	{
		u4Byte	tmp4Byte = PlatformEFIORead4Byte(Adapter, REG_SYS_SWR_CTRL1_8192E);
		PlatformEFIOWrite1Byte(Adapter,REG_SYS_SWR_CTRL2_8192E,0x75);
		tmp4Byte=  (tmp4Byte & 0xfff00fff)|(0x7E<<12);
		PlatformEFIOWrite4Byte(Adapter,REG_SYS_SWR_CTRL1_8192E,tmp4Byte );
	}
	//misc
	{
		int i;		
		u8 mac_addr[6];
		for(i=0; i<6; i++)
		{			
#ifdef CONFIG_CONCURRENT_MODE
			if(Adapter->iface_type == IFACE_PORT1)
				mac_addr[i] = rtw_read8(Adapter, REG_MACID1+i);
			else
#endif
			mac_addr[i] = rtw_read8(Adapter, REG_MACID+i);		
		}
		
		DBG_8192C(ADPT_FMT" MAC Address from REG_MACID = "MAC_FMT"\n", ADPT_ARG(Adapter),MAC_ARG(mac_addr));
	}

exit:
HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_END);

	DBG_871X("%s in %dms\n", __FUNCTION__, rtw_get_passing_time_ms(init_start_time));

	#ifdef DBG_HAL_INIT_PROFILING
	hal_init_stages_timestamp[HAL_INIT_STAGES_END]=rtw_get_current_time();

	for(hal_init_profiling_i=0;hal_init_profiling_i<HAL_INIT_STAGES_NUM-1;hal_init_profiling_i++) {
		DBG_871X("DBG_HAL_INIT_PROFILING: %35s, %u, %5u, %5u\n"
			, hal_init_stages_str[hal_init_profiling_i]
			, hal_init_stages_timestamp[hal_init_profiling_i]
			, (hal_init_stages_timestamp[hal_init_profiling_i+1]-hal_init_stages_timestamp[hal_init_profiling_i])
			, rtw_get_time_interval_ms(hal_init_stages_timestamp[hal_init_profiling_i], hal_init_stages_timestamp[hal_init_profiling_i+1])
		);
	}	
	#endif


_func_exit_;

	return status;
}

VOID
hal_poweroff_8192eu(
	IN	PADAPTER			Adapter 
)
{
	u8	u1bTmp;
	u8 bMacPwrCtrlOn = _FALSE;

	rtw_hal_get_hwreg(Adapter, HW_VAR_APFM_ON_MAC, &bMacPwrCtrlOn);
	if(bMacPwrCtrlOn == _FALSE)	
		return ;
	
	DBG_871X(" %s\n",__FUNCTION__);

	//Stop Tx Report Timer. 0x4EC[Bit1]=b'0
	u1bTmp = rtw_read8(Adapter, REG_TX_RPT_CTRL);
	rtw_write8(Adapter, REG_TX_RPT_CTRL, u1bTmp&(~BIT1));

	// stop rx 
	rtw_write8(Adapter, REG_CR, 0x0);

	HalPwrSeqCmdParsing(Adapter, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, Rtl8192E_NIC_LPS_ENTER_FLOW);

	// MCUFWDL 0x80[1:0]=0				// reset MCU ready status
	rtw_write8(Adapter, REG_MCUFWDL, 0x00);
#if 0	
	if((rtw_read8(Adapter, REG_MCUFWDL)&RAM_DL_SEL) && 
		Adapter->bFWReady) //8051 RAM code
	{
		_8051Reset8192E(Adapter);
	}
#else
	// Reset MCU IO Wrapper
	u1bTmp = rtw_read8(Adapter, REG_RSV_CTRL+1);
	rtw_write8(Adapter,REG_RSV_CTRL+1, (u1bTmp&(~BIT0)));
	
	// Reset MCU. Suggested by Filen. 2011.01.26. by tynli.
	u1bTmp = rtw_read8(Adapter, REG_SYS_FUNC_EN+1);
	rtw_write8(Adapter, REG_SYS_FUNC_EN+1, (u1bTmp&(~BIT2)));

	// Enable MCU IO Wrapper , for IPS flow
	u1bTmp = rtw_read8(Adapter, REG_RSV_CTRL+1);
	rtw_write8(Adapter, REG_RSV_CTRL+1, u1bTmp|BIT0);	
#endif
	

	// Card disable power action flow
	HalPwrSeqCmdParsing(Adapter, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, Rtl8192E_NIC_DISABLE_FLOW);
	
	bMacPwrCtrlOn = _FALSE;
	rtw_hal_set_hwreg(Adapter, HW_VAR_APFM_ON_MAC, &bMacPwrCtrlOn);	
}

static void rtl8192e_hw_power_down(_adapter *padapter)
{
	// 2010/-8/09 MH For power down module, we need to enable register block contrl reg at 0x1c.
	// Then enable power down control bit of register 0x04 BIT4 and BIT15 as 1.
		
	// Enable register area 0x0-0xc.
	rtw_write8(padapter,REG_RSV_CTRL, 0x0);			
	rtw_write16(padapter, REG_APS_FSMCO, 0x8812);
}

u32 rtl8192eu_hal_deinit(PADAPTER Adapter)
 {
	struct pwrctrl_priv *pwrctl = adapter_to_pwrctl(Adapter);
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
   	DBG_8192C("==> %s \n",__FUNCTION__);

	
	rtw_write16(Adapter, REG_GPIO_MUXCFG, rtw_read16(Adapter, REG_GPIO_MUXCFG)&(~BIT12));
	

	if(pHalData->bSupportUSB3 == _TRUE)
	{
		// set Reg 0xf008[3:4] to 2'11 to eable U1/U2 Mode in USB3.0. added by page, 20120712
		rtw_write8(Adapter, 0xf008, rtw_read8(Adapter, 0xf008)|0x18);
	}

	rtw_write32(Adapter, REG_HISR0_8192E, 0xFFFFFFFF);
	rtw_write32(Adapter, REG_HISR1_8192E, 0xFFFFFFFF);
	rtw_write32(Adapter, REG_HIMR0_8192E, IMR_DISABLED_8192E);
	rtw_write32(Adapter, REG_HIMR1_8192E, IMR_DISABLED_8192E);

 #ifdef SUPPORT_HW_RFOFF_DETECTED
 	DBG_8192C("bkeepfwalive(%x)\n", pwrctl->bkeepfwalive);
 	if(pwrctl->bkeepfwalive)
 	{
		_ps_close_RF(Adapter);		
		if((pwrctl->bHWPwrPindetect) && (pwrctl->bHWPowerdown))
			rtl8192e_hw_power_down(Adapter);
 	}
	else
#endif
	{	
		if(Adapter->hw_init_completed == _TRUE){
			hal_poweroff_8192eu(Adapter);

			if((pwrctl->bHWPwrPindetect ) && (pwrctl->bHWPowerdown))
				rtl8192e_hw_power_down(Adapter);
		}
		pHalData->bMacPwrCtrlOn = _FALSE;
		
	}		
	return _SUCCESS;
 }


unsigned int rtl8192eu_inirp_init(PADAPTER Adapter)
{	
	u8 i;	
	struct recv_buf *precvbuf;
	uint	status;
	struct dvobj_priv *pdev= adapter_to_dvobj(Adapter);
	struct intf_hdl * pintfhdl=&Adapter->iopriv.intf;
	struct recv_priv *precvpriv = &(Adapter->recvpriv);	
	u32 (*_read_port)(struct intf_hdl *pintfhdl, u32 addr, u32 cnt, u8 *pmem);
#ifdef CONFIG_USB_INTERRUPT_IN_PIPE
	HAL_DATA_TYPE *pHalData = GET_HAL_DATA(Adapter);
	u32 (*_read_interrupt)(struct intf_hdl *pintfhdl, u32 addr);
#endif

_func_enter_;

	_read_port = pintfhdl->io_ops._read_port;

	status = _SUCCESS;

	RT_TRACE(_module_hci_hal_init_c_,_drv_info_,("===> usb_inirp_init \n"));	
		
	precvpriv->ff_hwaddr = RECV_BULK_IN_ADDR;

	//issue Rx irp to receive data	
	precvbuf = (struct recv_buf *)precvpriv->precv_buf;	
	for(i=0; i<NR_RECVBUFF; i++)
	{
		if(_read_port(pintfhdl, precvpriv->ff_hwaddr, 0, (unsigned char *)precvbuf) == _FALSE )
		{
			RT_TRACE(_module_hci_hal_init_c_,_drv_err_,("usb_rx_init: usb_read_port error \n"));
			status = _FAIL;
			goto exit;
		}
		
		precvbuf++;		
		precvpriv->free_recv_buf_queue_cnt--;
	}

#ifdef CONFIG_USB_INTERRUPT_IN_PIPE
/* TDLS TODO: the following would let compile error */
#if 0
	if(pHalData->RtIntInPipe != 0x05)
	{
		status = _FAIL;
		DBG_871X("%s =>Warning !! Have not USB Int-IN pipe,  pHalData->RtIntInPipe(%d)!!!\n",__FUNCTION__,pHalData->RtIntInPipe);
		goto exit;
	}	
#endif
	_read_interrupt = pintfhdl->io_ops._read_interrupt;
	if(_read_interrupt(pintfhdl, RECV_INT_IN_ADDR) == _FALSE )
	{
		RT_TRACE(_module_hci_hal_init_c_,_drv_err_,("usb_rx_init: usb_read_interrupt error \n"));
		status = _FAIL;
	}
#endif

exit:
	
	RT_TRACE(_module_hci_hal_init_c_,_drv_info_,("<=== usb_inirp_init \n"));

_func_exit_;

	return status;

}

unsigned int rtl8192eu_inirp_deinit(PADAPTER Adapter)
{	
	RT_TRACE(_module_hci_hal_init_c_,_drv_info_,("\n ===> usb_rx_deinit \n"));
	
	rtw_read_port_cancel(Adapter);

	RT_TRACE(_module_hci_hal_init_c_,_drv_info_,("\n <=== usb_rx_deinit \n"));

	return _SUCCESS;
}

//-------------------------------------------------------------------
//
//	EEPROM/EFUSE Content Parsing
//
//-------------------------------------------------------------------
VOID
hal_ReadIDs_8192EU(
	IN	PADAPTER	Adapter,
	IN	pu1Byte		PROMContent,
	IN	BOOLEAN		AutoloadFail
	)
{
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	EEPROM_EFUSE_PRIV	*pEEPROM = GET_EEPROM_EFUSE_PRIV(Adapter);

	if( !AutoloadFail )
	{
		// VID, PID 
		
		pHalData->EEPROMVID = EF2Byte( *(u16 *)&PROMContent[EEPROM_VID_8192EU] );
		pHalData->EEPROMPID = EF2Byte( *(u16 *)&PROMContent[EEPROM_PID_8192EU] );		
		

		
		// Customer ID, 0x00 and 0xff are reserved for Realtek. 		
		pHalData->EEPROMCustomerID = *(u8 *)&PROMContent[EEPROM_CustomID_8192E];
		pHalData->EEPROMSubCustomerID = EEPROM_Default_SubCustomerID;

	}
	else
	{
		pHalData->EEPROMVID 			= EEPROM_Default_VID;
		pHalData->EEPROMPID 			= EEPROM_Default_PID;

		// Customer ID, 0x00 and 0xff are reserved for Realtek. 		
		pHalData->EEPROMCustomerID		= EEPROM_Default_CustomerID;
		pHalData->EEPROMSubCustomerID	= EEPROM_Default_SubCustomerID;

	}

	if((pHalData->EEPROMVID == 0x050D) && (pHalData->EEPROMPID == 0x1106))// SerComm for Belkin.
		pEEPROM->CustomerID = RT_CID_819x_Sercomm_Belkin;
	else if((pHalData->EEPROMVID == 0x0846) && (pHalData->EEPROMPID == 0x9051))// SerComm for Netgear.
		pEEPROM->CustomerID = RT_CID_819x_Sercomm_Netgear;
	else if((pHalData->EEPROMVID == 0x2001) && (pHalData->EEPROMPID == 0x330e))//add by ylb 20121012 for customer led for alpha
		pEEPROM->CustomerID = RT_CID_819x_ALPHA_Dlink;
	
	DBG_871X("VID = 0x%04X, PID = 0x%04X\n", pHalData->EEPROMVID, pHalData->EEPROMPID);
	DBG_871X("Customer ID: 0x%02X, SubCustomer ID: 0x%02X\n", pHalData->EEPROMCustomerID, pHalData->EEPROMSubCustomerID);
}

VOID
hal_ReadMACAddress_8192EU(
	IN	PADAPTER	Adapter,	
	IN	u8*			PROMContent,
	IN	BOOLEAN		AutoloadFail
	)
{
	EEPROM_EFUSE_PRIV *pEEPROM = GET_EEPROM_EFUSE_PRIV(Adapter);

	if(_FALSE == AutoloadFail)  
	{
		_rtw_memcpy(pEEPROM->mac_addr, &PROMContent[EEPROM_MAC_ADDR_8192EU], ETH_ALEN);
	}
	else
	{
		//Random assigh MAC address
		u8	sMacAddr[ETH_ALEN] = {0x00, 0xE0, 0x4C, 0x88, 0x12, 0x00};
		//sMacAddr[5] = (u8)GetRandomNumber(1, 254);
		_rtw_memcpy(pEEPROM->mac_addr, sMacAddr, ETH_ALEN);
	}

	DBG_8192C("%s MAC Address from EFUSE = "MAC_FMT"\n",__FUNCTION__, MAC_ARG(pEEPROM->mac_addr));
}


VOID
hal_CustomizedBehavior_8192EU(
	IN	PADAPTER	Adapter
	)
{
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);	
	EEPROM_EFUSE_PRIV	*pEEPROM = GET_EEPROM_EFUSE_PRIV(Adapter);
	struct led_priv	*pledpriv = &(Adapter->ledpriv);

	
	// Led mode
	switch(pEEPROM->CustomerID)
	{
		case RT_CID_DEFAULT:
			pledpriv->LedStrategy = SW_LED_MODE1;
			pledpriv->bRegUseLed = _TRUE;			
			break;

		case RT_CID_819x_HP:
			pledpriv->LedStrategy = SW_LED_MODE6; // Customize Led mode	
			break;
			
		case RT_CID_819x_Sercomm_Belkin:
			pledpriv->LedStrategy = SW_LED_MODE9;
			break;	

		case RT_CID_819x_Sercomm_Netgear:
			pledpriv->LedStrategy = SW_LED_MODE10;
			break;		
			
		case RT_CID_819x_ALPHA_Dlink://add by ylb 20121012 for customer led for alpha
			pledpriv->LedStrategy = SW_LED_MODE1;
			break;	
			
		default:
			pledpriv->LedStrategy = SW_LED_MODE9;
			break;			
	}

	// 2010.04.28 for 88CU minicard led control
	//if(pHalData->InterfaceSel == INTF_SEL2_MINICARD)
	//{
	//	pHalData->LedStrategy = SW_LED_MODE6;
	//}
	pHalData->bLedOpenDrain = _TRUE;// Support Open-drain arrangement for controlling the LED. Added by Roger, 2009.10.16.
}

static void
hal_CustomizeByCustomerID_8192EU(
	IN	PADAPTER		padapter
	)
{
#if 0
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(padapter);
	EEPROM_EFUSE_PRIV	*pEEPROM = GET_EEPROM_EFUSE_PRIV(padapter);

	// For customized behavior.
	if((pHalData->EEPROMVID == 0x103C) && (pHalData->EEPROMPID == 0x1629))// HP Lite-On for RTL8188CUS Slim Combo.
		pEEPROM->CustomerID = RT_CID_819x_HP; 
	else if ((pHalData->EEPROMVID == 0x9846) && (pHalData->EEPROMPID == 0x9041))
		pEEPROM->CustomerID = RT_CID_NETGEAR;
	else if ((pHalData->EEPROMVID == 0x2019) && (pHalData->EEPROMPID == 0x1201))
		pEEPROM->CustomerID = RT_CID_PLANEX;
	else if((pHalData->EEPROMVID == 0x0BDA) &&(pHalData->EEPROMPID == 0x5088))
		pEEPROM->CustomerID = RT_CID_CC_C;
	
	DBG_871X("PID= 0x%x, VID=  %x\n",pHalData->EEPROMPID,pHalData->EEPROMVID);
	
	//	Decide CustomerID according to VID/DID or EEPROM
	switch(pHalData->EEPROMCustomerID)
	{
		case EEPROM_CID_DEFAULT:
			if((pHalData->EEPROMVID == 0x2001) && (pHalData->EEPROMPID == 0x3308))
				pEEPROM->CustomerID = RT_CID_DLINK;
			else if((pHalData->EEPROMVID == 0x2001) && (pHalData->EEPROMPID == 0x3309))
				pEEPROM->CustomerID = RT_CID_DLINK;
			else if((pHalData->EEPROMVID == 0x2001) && (pHalData->EEPROMPID == 0x330a))
				pEEPROM->CustomerID = RT_CID_DLINK;
			else if((pHalData->EEPROMVID == 0x0BFF) && (pHalData->EEPROMPID == 0x8160))
			{
				pHalData->bAutoConnectEnable = _FALSE;
				pEEPROM->CustomerID = RT_CID_CHINA_MOBILE;
			}	
			else if((pHalData->EEPROMVID == 0x0BDA) &&	(pHalData->EEPROMPID == 0x5088))
				pEEPROM->CustomerID = RT_CID_CC_C;
	
			DBG_871X("PID= 0x%x, VID=  %x\n",pHalData->EEPROMPID,pHalData->EEPROMVID);
			break;
		case EEPROM_CID_WHQL:
			//padapter->bInHctTest = TRUE;
	
			//pMgntInfo->bSupportTurboMode = FALSE;
			//pMgntInfo->bAutoTurboBy8186 = FALSE;
	
			//pMgntInfo->PowerSaveControl.bInactivePs = FALSE;
			//pMgntInfo->PowerSaveControl.bIPSModeBackup = FALSE;
			//pMgntInfo->PowerSaveControl.bLeisurePs = FALSE;
			//pMgntInfo->PowerSaveControl.bLeisurePsModeBackup = FALSE;
			//pMgntInfo->keepAliveLevel = 0;
	
			//padapter->bUnloadDriverwhenS3S4 = FALSE;
			break;			
		default:
			pEEPROM->CustomerID = RT_CID_DEFAULT;
			break;
			
	}
	DBG_871X("MGNT Customer ID: 0x%2x\n", pEEPROM->CustomerID);
	
	hal_CustomizedBehavior_8192EU(padapter);
#endif
}


static VOID
ReadLEDSetting_8192EU(
	IN	PADAPTER	Adapter,	
	IN	u8*		PROMContent,
	IN	BOOLEAN		AutoloadFail
	)
{
	struct led_priv *pledpriv = &(Adapter->ledpriv);
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	EEPROM_EFUSE_PRIV	*pEEPROM = GET_EEPROM_EFUSE_PRIV(Adapter);
	
#ifdef CONFIG_SW_LED
	pledpriv->bRegUseLed = _TRUE;

	switch(pEEPROM->CustomerID)
	{
		default:
			pledpriv->LedStrategy = SW_LED_MODE1;
			break;
	}
	pHalData->bLedOpenDrain = _TRUE;// Support Open-drain arrangement for controlling the LED. Added by Roger, 2009.10.16.
#else // HW LED
	pledpriv->LedStrategy = HW_LED;
#endif //CONFIG_SW_LED
}

VOID
InitAdapterVariablesByPROM_8192EU(
	IN	PADAPTER	Adapter
	)
{
	EEPROM_EFUSE_PRIV *pEEPROM = GET_EEPROM_EFUSE_PRIV(Adapter);

#ifdef CONFIG_EFUSE_CONFIG_FILE
	Rtw_Hal_readPGDataFromConfigFile(Adapter);
#else //CONFIG_EFUSE_CONFIG_FILE
	hal_InitPGData_8192E(Adapter, pEEPROM->efuse_eeprom_data);
#endif	
	Hal_EfuseParseIDCode8192E(Adapter, pEEPROM->efuse_eeprom_data);
	
	Hal_ReadPROMVersion8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	hal_ReadIDs_8192EU(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	
#ifdef CONFIG_EFUSE_CONFIG_FILE
	Rtw_Hal_ReadMACAddrFromFile(Adapter);
#else //CONFIG_EFUSE_CONFIG_FILE
	hal_ReadMACAddress_8192EU(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
#endif //CONFIG_EFUSE_CONFIG_FILE

	Hal_ReadPowerSavingMode8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	Hal_ReadTxPowerInfo8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	Hal_ReadBoardType8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);

	//
	// Read Bluetooth co-exist and initialize
	//
	Hal_EfuseParseBTCoexistInfo8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	
	Hal_ReadChannelPlan8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	Hal_EfuseParseXtal_8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);	
	Hal_ReadThermalMeter_8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	Hal_ReadAntennaDiversity8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	Hal_ReadPAType_8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	Hal_ReadAmplifierType_8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	Hal_ReadRFEType_8192E(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
	hal_CustomizeByCustomerID_8192EU(Adapter);

	ReadLEDSetting_8192EU(Adapter, pEEPROM->efuse_eeprom_data, pEEPROM->bautoload_fail_flag);
}

static void Hal_ReadPROMContent_8192EU(
	IN PADAPTER 		Adapter
	)
{	
	EEPROM_EFUSE_PRIV *pEEPROM = GET_EEPROM_EFUSE_PRIV(Adapter);
	u8			eeValue;

	/* check system boot selection */
	eeValue = rtw_read8(Adapter, REG_SYS_EEPROM_CTRL);
	pEEPROM->EepromOrEfuse		= (eeValue & EEPROMSEL) ? _TRUE : _FALSE;
	pEEPROM->bautoload_fail_flag	= (eeValue & EEPROM_EN) ? _FALSE : _TRUE;

	DBG_8192C("Boot from %s, Autoload %s !\n", (pEEPROM->EepromOrEfuse ? "EEPROM" : "EFUSE"),
				(pEEPROM->bautoload_fail_flag ? "Fail" : "OK") );

	//pHalData->EEType = IS_BOOT_FROM_EEPROM(Adapter) ? EEPROM_93C46 : EEPROM_BOOT_EFUSE;

	InitAdapterVariablesByPROM_8192EU(Adapter);
}



VOID
hal_CustomizedBehavior_8192eu(
	IN PADAPTER 		Adapter
	)
{
#if 0
	PMGNT_INFO		pMgntInfo = &(Adapter->MgntInfo);
	
	// DTM test, we need to disable all power save mode.
	if(Adapter->bInHctTest)
	{
		pMgntInfo->PowerSaveControl.bInactivePs = FALSE;
		pMgntInfo->PowerSaveControl.bIPSModeBackup = FALSE;
		pMgntInfo->PowerSaveControl.bLeisurePs = FALSE;
		pMgntInfo->PowerSaveControl.bLeisurePsModeBackup =FALSE;
		pMgntInfo->keepAliveLevel = 0;
		pMgntInfo->dot11CurrentChannelNumber = 10;
		pMgntInfo->Regdot11ChannelNumber = 10;
	}	
#endif
}

void
ReadAdapterInfo8192EU(
	IN PADAPTER			Adapter
	)
{
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	
	DBG_871X("====> ReadAdapterInfo8192EU\n");

	// Read all content in Efuse/EEPROM.
	Hal_ReadPROMContent_8192EU(Adapter);

	// We need to define the RF type after all PROM value is recognized.
	hal_ReadRFType_8192E(Adapter);

	// 2011/02/09 MH We gather the same value for all USB series IC.
	hal_CustomizedBehavior_8192eu(Adapter);

	DBG_871X("ReadAdapterInfo8192EU <====\n");
}

void UpdateInterruptMask8192EU(PADAPTER padapter,u8 bHIMR0 ,u32 AddMSR, u32 RemoveMSR)
{
	HAL_DATA_TYPE *pHalData;

	u32 *himr;
	pHalData = GET_HAL_DATA(padapter);

	if(bHIMR0)
		himr = &(pHalData->IntrMask[0]);
	else
		himr = &(pHalData->IntrMask[1]);
	
	if (AddMSR)
		*himr |= AddMSR;

	if (RemoveMSR)
		*himr &= (~RemoveMSR);

	if(bHIMR0)	
		rtw_write32(padapter, REG_HIMR0_8192E, *himr);
	else
		rtw_write32(padapter, REG_HIMR1_8192E, *himr);	

}

void SetHwReg8192EU(PADAPTER Adapter, u8 variable, u8* val)
{
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	struct dm_priv	*pdmpriv = &pHalData->dmpriv;
	DM_ODM_T 		*podmpriv = &pHalData->odmpriv;

#if defined(CONFIG_WOWLAN) || defined(CONFIG_AP_WOWLAN)
	struct wowlan_ioctl_param *poidparam;
	struct recv_buf *precvbuf;
	struct pwrctrl_priv *pwrctl = adapter_to_pwrctl(Adapter);
	int res, i;
	u32 tmp;
	u16 len = 0;
	u8 mstatus = (*(u8 *)val);
	u8 trycnt = 100;
	u8 data[4];
#endif

_func_enter_;

	switch(variable)
	{
		case HW_VAR_RXDMA_AGG_PG_TH:
			#ifdef CONFIG_USB_RX_AGGREGATION
			{
				//threshold == 1 , Disable Rx-agg when AP is B/G mode or wifi_spec=1 to prevent bad TP.
				
				u8	threshold = *((u8 *)val);
				if( threshold == 0){
					threshold = (pHalData->RegAcUsbDmaSize & 0x0F);
				}
				rtw_write8(Adapter, REG_RXDMA_AGG_PG_TH, threshold);

				#ifdef CONFIG_80211N_HT
				{	
					// 2014-07-24 Fix WIFI Logo -5.2.4/5.2.9 - DT3 low TP issue
					// Adjust RxAggrTimeout to close to zero disable RxAggr for RxAgg-USB mode, suggested by designer
					// Timeout value is calculated by 34 / (2^n)

					struct mlme_priv	*pmlmepriv = &Adapter->mlmepriv;
					struct ht_priv		*phtpriv = &pmlmepriv->htpriv;		
					
					if(pHalData->UsbRxAggMode == USB_RX_AGG_USB){
						#if 1
						//BG mode || (wifi_spec=1 && BG mode Testbed)	
						if((threshold == 1) && (_FALSE == phtpriv->ht_option) )						
						#else
						//(wifi_spec=1 && BG mode Testbed)
						if((Adapter->registrypriv.wifi_spec==1) && (_FALSE == phtpriv->ht_option) )
						#endif												
							rtw_write8(Adapter, REG_RXDMA_AGG_PG_TH+1, 0);					
					}
				}
				#endif//#ifdef CONFIG_80211N_HT
				
			}
			#endif
			break;
		case HW_VAR_SET_RPWM:
#ifdef CONFIG_LPS_LCLK
			{
				u8	ps_state = *((u8 *)val);
				//rpwm value only use BIT0(clock bit) ,BIT6(Ack bit), and BIT7(Toggle bit) for 88e.
				//BIT0 value - 1: 32k, 0:40MHz.
				//BIT6 value - 1: report cpwm value after success set, 0:do not report.
				//BIT7 value - Toggle bit change.
				//modify by Thomas. 2012/4/2.
				ps_state = ps_state & 0xC1;
				//DBG_871X("##### Change RPWM value to = %x for switch clk #####\n",ps_state);
				rtw_write8(Adapter, REG_USB_HRPWM, ps_state);
			}
#endif
#ifdef CONFIG_AP_WOWLAN
			if (pwrctl->wowlan_ap_mode == _TRUE)
			{
				u8	ps_state = *((u8 *)val);
				DBG_871X("%s, RPWM\n", __func__);
				//rpwm value only use BIT0(clock bit) ,BIT6(Ack bit), and BIT7(Toggle bit) for 88e.
				//BIT0 value - 1: 32k, 0:40MHz.
				//BIT6 value - 1: report cpwm value after success set, 0:do not report.
				//BIT7 value - Toggle bit change.
				//modify by Thomas. 2012/4/2.
				ps_state = ps_state & 0xC1;
				//DBG_871X("##### Change RPWM value to = %x for switch clk #####\n",ps_state);
				rtw_write8(Adapter, REG_USB_HRPWM, ps_state);
			}
#endif
			break;
#ifdef CONFIG_WOWLAN_OLD
		case HW_VAR_WOWLAN:
			{
			poidparam = (struct wowlan_ioctl_param *)val;
			switch (poidparam->subcode){
				case WOWLAN_ENABLE:
					DBG_871X_LEVEL(_drv_always_, "WOWLAN_ENABLE\n");

					SetFwRelatedForWoWLAN8192E(Adapter, _TRUE);

					//Set Pattern
					//if(pwrctl->wowlan_pattern==_TRUE)
					//	rtw_wowlan_reload_pattern(Adapter);

					//RX DMA stop
					DBG_871X_LEVEL(_drv_always_, "Pause DMA\n");
					rtw_write32(Adapter,REG_RXPKT_NUM,(rtw_read32(Adapter,REG_RXPKT_NUM)|RW_RELEASE_EN));
					do{
						if((rtw_read32(Adapter, REG_RXPKT_NUM)&RXDMA_IDLE)) {
							DBG_871X_LEVEL(_drv_always_, "RX_DMA_IDLE is true\n");
							break;
						} else {
							// If RX_DMA is not idle, receive one pkt from DMA
							DBG_871X_LEVEL(_drv_always_, "RX_DMA_IDLE is not true\n");
						}
					}while(trycnt--);
					if(trycnt ==0)
						DBG_871X_LEVEL(_drv_always_, "Stop RX DMA failed...... \n");

					//Set WOWLAN H2C command.
					DBG_871X_LEVEL(_drv_always_, "Set WOWLan cmd\n");
					rtl8192e_set_wowlan_cmd(Adapter, 1);

					mstatus = rtw_read8(Adapter, REG_WOW_CTRL);
					trycnt = 10;

					while(!(mstatus&BIT1) && trycnt>1) {
						mstatus = rtw_read8(Adapter, REG_WOW_CTRL);
						DBG_871X_LEVEL(_drv_always_, "Loop index: %d :0x%02x\n", trycnt, mstatus);
						trycnt --;
						rtw_msleep_os(2);
					}

					pwrctl->wowlan_wake_reason = rtw_read8(Adapter, REG_WOWLAN_WAKE_REASON);
					DBG_871X_LEVEL(_drv_always_, "wowlan_wake_reason: 0x%02x\n",
										pwrctl->wowlan_wake_reason);

					if (Adapter->intf_stop)
						Adapter->intf_stop(Adapter);

					// Invoid SE0 reset signal during suspending
					rtw_write8(Adapter, REG_RSV_CTRL, 0x20);
					rtw_write8(Adapter, REG_RSV_CTRL, 0x60);

					//rtw_msleep_os(10);
					break;
				case WOWLAN_DISABLE:
					DBG_871X_LEVEL(_drv_always_, "WOWLAN_DISABLE\n");
					trycnt = 10;
					// 1. Read wakeup reason
					pwrctl->wowlan_wake_reason = rtw_read8(Adapter, REG_WOWLAN_WAKE_REASON);
					DBG_871X_LEVEL(_drv_always_, "wakeup_reason: 0x%02x, mac_630=0x%08x, mac_634=0x%08x, mac_1c0=0x%08x, mac_1c4=0x%08x"
					", mac_494=0x%08x, , mac_498=0x%08x, mac_49c=0x%08x, mac_608=0x%08x, mac_4a0=0x%08x, mac_4a4=0x%08x\n"
					", mac_1cc=0x%08x, mac_2f0=0x%08x, mac_2f4=0x%08x, mac_2f8=0x%08x, mac_2fc=0x%08x, mac_8c=0x%08x"
					, pwrctl->wowlan_wake_reason, rtw_read32(Adapter, 0x630), rtw_read32(Adapter, 0x634)
					, rtw_read32(Adapter, 0x1c0), rtw_read32(Adapter, 0x1c4)
					, rtw_read32(Adapter, 0x494), rtw_read32(Adapter, 0x498), rtw_read32(Adapter, 0x49c), rtw_read32(Adapter, 0x608)
					, rtw_read32(Adapter, 0x4a0), rtw_read32(Adapter, 0x4a4)
					, rtw_read32(Adapter, 0x1cc), rtw_read32(Adapter, 0x2f0), rtw_read32(Adapter, 0x2f4), rtw_read32(Adapter, 0x2f8)
					, rtw_read32(Adapter, 0x2fc), rtw_read32(Adapter, 0x8c));

					rtl8192e_set_wowlan_cmd(Adapter, 0);
					mstatus = rtw_read8(Adapter, REG_WOW_CTRL);
					DBG_871X_LEVEL(_drv_info_, "%s mstatus:0x%02x\n", __func__, mstatus);

					while(mstatus&BIT1 && trycnt>1) {
						mstatus = rtw_read8(Adapter, REG_WOW_CTRL);
						DBG_871X_LEVEL(_drv_always_, "Loop index: %d :0x%02x\n", trycnt, mstatus);
						trycnt --;
						rtw_msleep_os(2);
					}

					if (mstatus & BIT1)
						printk("System did not release RX_DMA\n");
					else
						SetFwRelatedForWoWLAN8192E(Adapter, _FALSE);

					rtw_msleep_os(2);
					if(!(pwrctl->wowlan_wake_reason & FWDecisionDisconnect))
						rtl8192e_set_FwJoinBssReport_cmd(Adapter, 1);
					//rtw_msleep_os(10);
					break;
				default:
					break;
			}
		}
		break;
#endif			
#ifdef CONFIG_AP_WOWLAN
		case HW_VAR_AP_WOWLAN:
		{
			poidparam = (struct wowlan_ioctl_param *)val;
			switch (poidparam->subcode) {
			case WOWLAN_AP_ENABLE:
				DBG_871X("%s, WOWLAN_AP_ENABLE\n", __func__);
				// 1. Download WOWLAN FW
				DBG_871X_LEVEL(_drv_always_, "Re-download WoWlan FW!\n");
#ifdef DBG_CHECK_FW_PS_STATE
				if(rtw_fw_ps_state(Adapter) == _FAIL) {
					pdbgpriv->dbg_enwow_dload_fw_fail_cnt++;
					DBG_871X_LEVEL(_drv_always_, "wowlan enable no leave 32k\n");
				}
#endif //DBG_CHECK_FW_PS_STATE
				do {
					if (rtw_read8(Adapter, REG_HMETFR) == 0x00) {
						DBG_871X_LEVEL(_drv_always_, "Ready to change FW.\n");
						break;
					}
					rtw_msleep_os(10);
					DBG_871X_LEVEL(_drv_always_, "trycnt: %d\n", (100-trycnt));
				} while (trycnt--);

				SetFwRelatedForWoWLAN8192E(Adapter, _TRUE);

				// 2. RX DMA stop
				DBG_871X_LEVEL(_drv_always_, "Pause DMA\n");
				trycnt = 100;
				rtw_write32(Adapter,REG_RXPKT_NUM,
					(rtw_read32(Adapter,REG_RXPKT_NUM)|RW_RELEASE_EN));
				do {
					if ((rtw_read32(Adapter, REG_RXPKT_NUM)&RXDMA_IDLE)) {
						DBG_871X_LEVEL(_drv_always_, "RX_DMA_IDLE is true\n");
						break;
					} else {
						// If RX_DMA is not idle, receive one pkt from DMA
						DBG_871X_LEVEL(_drv_always_, "RX_DMA_IDLE is not true\n");
					}
				} while (trycnt--);

				if (trycnt == 0)
					DBG_871X_LEVEL(_drv_always_, "Stop RX DMA failed...... \n");

				// 5. Set Enable WOWLAN H2C command.
				DBG_871X_LEVEL(_drv_always_, "Set Enable AP WOWLan cmd\n");
				rtl8192e_set_ap_wowlan_cmd(Adapter, 1);
				// 6. add some delay for H2C cmd ready
				rtw_msleep_os(10);
				// 7. enable AP power save
				rtl8192e_set_ap_ps_wowlan_cmd(Adapter, 1);

				rtw_write8(Adapter, REG_WOWLAN_WAKE_REASON, 0);

				if (Adapter->intf_stop)
					Adapter->intf_stop(Adapter);

				// Invoid SE0 reset signal during suspending
				rtw_write8(Adapter, REG_RSV_CTRL, 0x20);
				rtw_write8(Adapter, REG_RSV_CTRL, 0x60);
				break;
			case WOWLAN_AP_DISABLE:
				DBG_871X("%s, WOWLAN_AP_DISABLE\n", __func__);
				// 1. Read wakeup reason
				pwrctl->wowlan_wake_reason =
					rtw_read8(Adapter, REG_WOWLAN_WAKE_REASON);

				DBG_871X_LEVEL(_drv_always_, "wakeup_reason: 0x%02x\n",
						pwrctl->wowlan_wake_reason);

				// 2. diable AP power save
				rtl8192e_set_ap_ps_wowlan_cmd(Adapter, 0);
				// 3.  Set Disable WOWLAN H2C command.
				DBG_871X_LEVEL(_drv_always_, "Set Disable WOWLan cmd\n");
				rtl8192e_set_ap_wowlan_cmd(Adapter, 0);
				// 6. add some delay for H2C cmd ready
				rtw_msleep_os(2);
#ifdef DBG_CHECK_FW_PS_STATE
				if (rtw_fw_ps_state(Adapter) == _FAIL) {
					pdbgpriv->dbg_diswow_dload_fw_fail_cnt++;
					DBG_871X_LEVEL(_drv_always_, "wowlan enable no leave 32k\n");
				}
#endif //DBG_CHECK_FW_PS_STATE

				DBG_871X_LEVEL(_drv_always_, "Release RXDMA\n");

				rtw_write32(Adapter, REG_RXPKT_NUM,
					(rtw_read32(Adapter,REG_RXPKT_NUM) & (~RW_RELEASE_EN)));

				do {
					if (rtw_read8(Adapter, REG_HMETFR) == 0x00) {
						DBG_871X_LEVEL(_drv_always_, "Ready to change FW.\n");
						break;
					}
					rtw_msleep_os(10);
					DBG_871X_LEVEL(_drv_always_, "trycnt: %d\n", (100-trycnt));
				} while (trycnt--);

				SetFwRelatedForWoWLAN8192E(Adapter, _FALSE);
#ifdef CONFIG_GPIO_WAKEUP
				DBG_871X_LEVEL(_drv_always_, "Set Wake GPIO to high for default.\n");
				HalSetOutPutGPIO(Adapter, WAKEUP_GPIO_IDX, 1);
#endif

#ifdef CONFIG_CONCURRENT_MODE
				if (rtw_buddy_adapter_up(Adapter) == _TRUE &&
					check_buddy_fwstate(Adapter, WIFI_AP_STATE) == _TRUE) {
					rtl8192e_set_FwJoinBssReport_cmd(Adapter->pbuddy_adapter, RT_MEDIA_CONNECT);
					issue_beacon(Adapter->pbuddy_adapter, 0);
				} else {
					rtl8192e_set_FwJoinBssReport_cmd(Adapter, RT_MEDIA_CONNECT);
					issue_beacon(Adapter, 0);
				}
#else
				rtl8192e_set_FwJoinBssReport_cmd(Adapter, RT_MEDIA_CONNECT);
				issue_beacon(Adapter, 0);
#endif

				break;
			default:
				break;
			}
		}
			break;
#endif //CONFIG_AP_WOWLAN
		default :
			SetHwReg8192E(Adapter, variable, val);
			break;
	}
}


void GetHwReg8192EU(PADAPTER Adapter, u8 variable, u8* val)
{
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	DM_ODM_T 		*podmpriv = &pHalData->odmpriv;
_func_enter_;

	switch(variable)
	{		
		default:
			GetHwReg8192E(Adapter,variable,val);
			break;
	}

_func_exit_;
}
u8
GetHalDefVar8192EUsb(
	IN	PADAPTER				Adapter,
	IN	HAL_DEF_VARIABLE		eVariable,
	IN	PVOID					pValue
	)
{
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	u8			bResult = _SUCCESS;

	switch(eVariable)
	{

		case HW_VAR_MAX_RX_AMPDU_FACTOR:
			*(( u32*)pValue) = MAX_AMPDU_FACTOR_64K; //MAX_AMPDU_FACTOR_64K;
			break;
		default:
			GetHalDefVar8192E(Adapter,eVariable,pValue);
			break;
	}
	return bResult;
}
//
//	Description:
//		Change default setting of specified variable.
//
u8
SetHalDefVar8192EUsb(
	IN	PADAPTER				Adapter,
	IN	HAL_DEF_VARIABLE		eVariable,
	IN	PVOID					pValue
	)
{
	HAL_DATA_TYPE	*pHalData = GET_HAL_DATA(Adapter);
	u8			bResult = _SUCCESS;

	switch(eVariable)
	{
		default:
			SetHalDefVar8192E(Adapter,eVariable,pValue);
			break;
	}
	return bResult;
}


void _update_response_rate(_adapter *padapter,unsigned int mask)
{
	u8	RateIndex = 0;
	// Set RRSR rate table.
	rtw_write8(padapter, REG_RRSR, mask&0xff);
	rtw_write8(padapter,REG_RRSR+1, (mask>>8)&0xff);

	// Set RTS initial rate
	// We just need to update to pHalData->RTSInitRate which will be set in Tx descriptor.
}

static void rtl8192eu_init_default_value(_adapter * padapter)
{
	 rtl8192e_init_default_value(padapter);
}

static u8 rtl8192eu_ps_func(PADAPTER Adapter,HAL_INTF_PS_FUNC efunc_id, u8 *val)
{	
	u8 bResult = _TRUE;
	switch(efunc_id){

		#if defined(CONFIG_AUTOSUSPEND) && defined(SUPPORT_HW_RFOFF_DETECTED)
		case HAL_USB_SELECT_SUSPEND:
			{
				u8 bfwpoll = *(( u8*)val);
				//rtl8188e_set_FwSelectSuspend_cmd(Adapter,bfwpoll ,500);//note fw to support hw power down ping detect
			}
			break;
		#endif //CONFIG_AUTOSUSPEND && SUPPORT_HW_RFOFF_DETECTED

		default:
			break;
	}
	return bResult;
}

void rtl8192eu_set_hal_ops(_adapter * padapter)
{
	struct hal_ops	*pHalFunc = &padapter->HalFunc;

_func_enter_;

	pHalFunc->hal_power_on = _InitPowerOn_8192EU;
	pHalFunc->hal_power_off = hal_poweroff_8192eu;

	pHalFunc->hal_init = &rtl8192eu_hal_init;
	pHalFunc->hal_deinit = &rtl8192eu_hal_deinit;

	pHalFunc->inirp_init = &rtl8192eu_inirp_init;
	pHalFunc->inirp_deinit = &rtl8192eu_inirp_deinit;

	pHalFunc->init_xmit_priv = &rtl8192eu_init_xmit_priv;
	pHalFunc->free_xmit_priv = &rtl8192eu_free_xmit_priv;

	pHalFunc->init_recv_priv = &rtl8192eu_init_recv_priv;
	pHalFunc->free_recv_priv = &rtl8192eu_free_recv_priv;
#ifdef CONFIG_SW_LED
	pHalFunc->InitSwLeds = &rtl8192eu_InitSwLeds;
	pHalFunc->DeInitSwLeds = &rtl8192eu_DeInitSwLeds;
#else //case of hw led or no led
	pHalFunc->InitSwLeds = NULL;
	pHalFunc->DeInitSwLeds = NULL;	
#endif//CONFIG_SW_LED
	
	pHalFunc->init_default_value = &rtl8192eu_init_default_value;
	pHalFunc->intf_chip_configure = &rtl8192eu_interface_configure;
	pHalFunc->read_adapter_info = &ReadAdapterInfo8192EU;

	pHalFunc->SetHwRegHandler = &SetHwReg8192EU;
	pHalFunc->GetHwRegHandler = &GetHwReg8192EU;
  	pHalFunc->GetHalDefVarHandler = &GetHalDefVar8192EUsb;
 	pHalFunc->SetHalDefVarHandler = &SetHalDefVar8192EUsb;
	
	pHalFunc->SetBeaconRelatedRegistersHandler = &SetBeaconRelatedRegisters8192E;

	pHalFunc->hal_xmit = &rtl8192eu_hal_xmit;
	pHalFunc->mgnt_xmit = &rtl8192eu_mgnt_xmit;
	pHalFunc->hal_xmitframe_enqueue = &rtl8192eu_hal_xmitframe_enqueue;


#ifdef CONFIG_HOSTAPD_MLME
	pHalFunc->hostap_mgnt_xmit_entry = &rtl8192eu_hostap_mgnt_xmit_entry;
#endif
	pHalFunc->interface_ps_func = &rtl8192eu_ps_func;
#ifdef CONFIG_XMIT_THREAD_MODE
	pHalFunc->xmit_thread_handler = &rtl8192eu_xmit_buf_handler;
#endif
	rtl8192e_set_hal_ops(pHalFunc);
_func_exit_;

}

